The Cheap and Easy Way to Finish Vacuum Lines




I’ve been doing composites for a few years now and I always see people using those through the bag type vacuum connectors like this connector from Fibre Glast. I see them in the mid $20 to close to $40 range depending on the supplier and the fittings it comes with. Believe it or not, I’ve actually never used one in the few years I’ve been doing composites. When I got started it was an expense I didn’t want to pay. Now I’m just so used to doing it my way, I just never got one (or a few if you have a few parts going at once). They seem to work nice so I have nothing against them, just never adapted to using them. Below is a picture of the cheap and easy ways the I fill, or cover the ends of vacuum or infusion lines. On the left is a semi rigid vacuum line with some bleeder taped onto the end. The bleeder helps distribute the vacuum across the part and it keeps the bag from getting sucked into the end of the line. If you utilize this type of vacuum line with Stretchlon 200, without the end of the line covered or filled, there is a very high likely hood of the vacuum actually popping a hole in the bag as it get sucked into the vacuum line. The second is a more flexible, softer line that I use mostly for infusions. I will get a small scrap of flow net, roll it up, and stuff it into the end of the line. This keeps the vacuum pressure from sucking down and closing off the end of the line. I’ll also use this technique with the harder white lines on the vacuum side of an infusion setup. It would be a good idea to get some cheap spring loaded clamps to keep the vacuum lines against the mold flange as they can pull themselves off sometimes. You can mix and match the tubes with either the bleeder or net as you see fit for your purpose.

There you have it. Two cheap ways to finish vacuum lines when you are getting up and going. Try it out and let me know what you think, or let me know if I should pick up a few of those through bag connectors.


36 thoughts on “The Cheap and Easy Way to Finish Vacuum Lines”

  1. Hey this is kind of of off topic but I was wanting to know if blogs use WYSIWYG editors or if you have to manually code with HTML. I’m starting a blog soon but have no coding knowledge so I wanted to get guidance from someone with experience. Any help would be enormously appreciated!

    1. Not sure if you listen to podcasts, but check out “Smart Passive Income” with Patt Flynn and start from episode one. I probably spend 10X the amount of time building this site as an expert, but its not that bad once you get into it. YouTube and Google will be your best friends when you try and get something set up and going. Good luck with your blog and send me a link once its up.

  2. Attractive element of content. I just stumbled upon your weblog and in accession capital to assert that I get actually loved account your weblog posts. Any way I will be subscribing in your augment and even I fulfillment you get entry to constantly fast.

  3. What’s up, yeah this paragraph is actually fastidious and I have learned lot of things from it regarding blogging. thanks.

  4. It’s a pity you don’t have a donate button! I’d definitely donate to this brilliant blog! I guess for now i’ll settle for bookmarking and adding your RSS feed to my Google account. I look forward to new updates and will talk about this blog with my Facebook group. Talk soon!

    1. I appreciate it! We may look into a donate button for those that feel inclined to do so. I’m just getting this blog going at the moment, and intend to keep the content free for everyone. As the blog gains traction and requires more of my time, I may look into bringing on ads, but I promise to not make them over powering. I want people to enjoy their experience on this site and walk away learning something. If you would like to help out, a lot of the links in our blog posts, or the Book Store are affiliate links. So at no extra cost to you, we get a small commission for sending you to the seller. Last thing, we just set up TheCompositesBlog@hotmail.com for anyone that wants to get onto our mailing list. Again, being a new site and I am not the “techy”, I have not set up an automatic email subscription just yet. Thanks!

    1. Thank you for the kind words. We try and bring a well rounded set of techniques and topics to the blog so just about anyone can learn something.

  5. I like using PEHD through bag connectors like these ones: https://www.google.fr/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0ahUKEwjXzqqLiPXWAhUHPxQKHRNyCoAQjRwIBw&url=https%3A%2F%2Fcompositeenvisions.com%2Fairtech-vac-ric-resin-infusion-connector-1-2-hole-and-groove-1602.html&psig=AOvVaw3_K5tt60qPFzO0eg8o0smE&ust=1508240529974455

    They are great through bag connectors both for the injection line and vacuum port. Being PEHD and monoblock they are much easier to use and reuse than metal through bag fittings.
    Though the metal one are the way to go for prepregs as the curing temperature can play havoc on the tubes and gum tape (plus if you do your prepreg right you shouldn’t suck any resin out through the vent).

  6. This is the perfect site for everyone who wants to find out about this topic.

    You know a whole lot its almost hard to argue with you (not
    that I actually will need to…HaHa). You certainly put
    a fresh spin on a subject which has been written about for
    decades. Wonderful stuff, just excellent!

  7. hello there and thank you for your information – I have definitely picked up anything new from right here. I did however expertise several technical points using this web site, since I experienced to reload the website many times previous to I could get it to load correctly. I had been wondering if your web hosting is OK? Not that I’m complaining, but sluggish loading instances times will sometimes affect your placement in google and could damage your high-quality score if ads and marketing with Adwords. Well I’m adding this RSS to my email and can look out for much more of your respective interesting content. Ensure that you update this again soon..

  8. We stumbled over here by a different web page and thought I
    may as well check things out. I like what I see so i
    am just following you. Look forward to looking at your web page yet again.

  9. Nice post. I was checking continuously this blog and I am impressed!
    Very helpful information specifically the last part 🙂 I care for such info much.

    I was looking for this particular information for a long time.
    Thank you and good luck.

    Here is my web site … ahmedabad escort

  10. My brother suggested I might like this blog. He was totally right.
    This post truly made my day. You cann’t imagine just how much time I had
    spent for this information! Thanks!

  11. I was curious if you ever thought of changing the structure
    of your website? Its very well written; I love what youve got to say.
    But maybe you could a little more in the way of content
    so people could connect with it better. Youve got an awful lot of text for only having 1 or 2 pictures.
    Maybe you could space it out better?

  12. Hey there! Quick question that’s totally off topic. Do
    you know how to make your site mobile friendly?
    My weblog looks weird when browsing from my apple
    iphone. I’m trying to find a theme or plugin that might be able to correct this problem.
    If you have any recommendations, please share.
    Cheers!

  13. Hello! I could have sworn I’ve visited this site before but after looking at some of the posts I realized it’s new to me.
    Anyways, I’m certainly delighted I came across it and
    I’ll be book-marking it and checking back regularly!

  14. Greetings from Florida! I’m bored at work so I decided to check
    out your site on my iphone during lunch break. I enjoy the
    information you provide here and can’t wait to take a look when I get home.
    I’m surprised at how fast your blog loaded on my mobile ..
    I’m not even using WIFI, just 3G .. Anyhow, amazing
    site!

  15. Hi there! This is kind of off topic but I need some guidance from an established blog.
    Is it hard to set up your own blog? I’m not very techincal but I can figure
    things out pretty fast. I’m thinking about setting up my own but I’m not sure where
    to begin. Do you have any points or suggestions?
    Cheers

    My web page – bodog88

  16. I have been browsing online more than 2 hours today,
    yet I never found any interesting article like yours.
    It’s pretty worth enough for me. In my view, if all web owners
    and bloggers made good content as you did, the net will be a lot more useful
    than ever before.

  17. I am curious to find out what blog platform you happen to be utilizing?
    I’m experiencing some minor security problems with my latest blog and I’d like to find something more safe.
    Do you have any recommendations?

  18. I am sure this paragraph has touched all the internet visitors, its really really nice piece of writing on building up new website.|

  19. Its such as you learn my thoughts! You appear to know a lot about this, such as you wrote the e-book in it or something. I think that you simply can do with a few to power the message home a little bit, but instead of that, that is magnificent blog. A fantastic read. I will definitely be back.|

  20. Hey there would you mind stating which blog platform you’re using? I’m planning to start my own blog in the near future but I’m having a hard time deciding between BlogEngine/Wordpress/B2evolution and Drupal. The reason I ask is because your design seems different then most blogs and I’m looking for something unique. P.S Apologies for getting off-topic but I had to ask!|

  21. Hello, Neat post. There’s a problem together with your website in web explorer, could test this?
    IE still is the market leader and a huge component of other people will leave out
    your great writing because of this problem.

Comments are closed.